fbpx

Tech Tips: Servicing Coolant Systems

The use of liquid cooling is at an all-time high for powersports engines. All modern liquid cooling systems use a pump to circulate the coolant through the system.

The use of liquid cooling is at an all-time high for powersports engines. All modern liquid cooling systems use a pump to circulate the coolant through the system. These water pumps should be inspected regularly as their seals can and do fail. Most water pumps have a built-in seal inspection feature called a tell-tale hole. The tell-tale hole is located directly below the water pump. The water pump’s mechanical seal has failed if coolant leaks from the hole.

The water pump impeller must be turned by the engine. The mechanical seal allows the engine to turn the water pump impeller while keeping the coolant and engine oil separate. The spring-loaded rubber seal pushes against a plastic seal ring on the water pump impeller to form a watertight seal, while allowing the shaft and impeller to rotate. In most cases, there is also a separate oil seal further down the water pump shaft to seal the engine oil. If coolant leaks past the mechanical seal, it will flow from the tell-tale hole.

Remove the impeller and/or shaft to access the mechanical seal. Note, many impellers have reverse threads, so consult the manual to be sure. Remove the mechanical by driving it out from the opposite side or carefully prying it out. Avoid damaging the seal or water pump cover mating surface by prying against them.

Sometimes, the failed mechanical seal will allow coolant to leak past it, causing the impeller shaft to rust. The corrosion can build up in the space between the mechanical and oil seals. The oil seal may not be far from failing as the impeller shaft becomes rough and pitted where it makes contact with the oil seal. In this case, the mechanical seal, oil seal, impeller shaft and bearings must be replaced. When disassembling a water pump for inspection, check the condition of the seals, bearings, impeller and shaft. Take the time and replace all of the suspect parts while they can be easily accessed.

It is generally recommended to replace the seals as a set. Often, the water pump shaft bearings must be removed to access the seals. Most manufacturers recommend replacing the bearings with new items if they are removed.

There are a few other types of water pump seals. Some models use a one-piece seal that acts as both a mechanical seal and oil seal. Others use two rubber oil seal type seals, one to seal the oil in and one to seal the coolant out. Always note the direction the seals sit before removal. Also, most water pumps have an impeller cover O-ring or gasket that can leak. Replace the O-ring or gasket seal anytime the cover is removed.

Drive in the new seals with a suitable driver that is the same outside diameter as the seal. Some mechanical seals may require a press or special mechanical seal installer tool. For a good seal against the case, mechanical seals may require the application of sealant between the metal mating surface of the seal and the case; others may come with a special coating from the factory. Always follow the instructions in the service manuals when replacing these seals. Some water pumps are not serviceable. These must be replaced as a unit if an internal seal fails.

Water pump seals can last for years without problems, or they can fail after a few months of use. Change the coolant according to the manufacturer’s periodic maintenance chart to help prevent water pump seal problems. Keep an eye out for tell-tale holes warning of faulty seals and encourage service customers to have their coolant systems serviced regularly.

Link: Cyclepedia

Cyclepedia Press LLC
Phone: (828) 645-0017Contact: Len Nelson

You May Also Like

Powersports Belt Maintenance Tips

Dayco’s new line of CVT belts are impressive, but you still need to know how to properly maintain them.

Dayco recently entered the powersports market with its Dayco POWER CVT belts. The new line includes a full range of specially engineered belts for various riding levels and engine sizes, including an extreme performance belt for heavily modified vehicles with engines over 800cc. As such, Dayco also wants to ensure you're aware of proper belt maintenance tips, so your belt and your vehicle are ready for peak performance.

Motorcycle Sales and Technology Trends for 2022

Supply shortages mean less tech, although motorcycles still have plenty of new features.

motorcycle, technology
Important Maintenance Checks for Motorcycle Storage

From the fuel and lube to the battery and tires, learn how you can keep your bike from corroding during the cold season.

battery, battery charger, maintenance
How to Properly Dispose of Motor Oil

Did you know that one gallon of motor oil can contaminate a million gallons of water if poured into a storm drain?

oil, motor oil, quick lube
Prepping Your Snowmobile for the Season

Get your snowmobile in shape this fall before hitting the trails.

snowmobile

Other Posts

Engine Ice’s Ice Water Racing Coolant

Engine Ice moves heat away from the engine faster and protects all engine parts, including cast iron, brass, steel, and rubber.

Snowmobile Engine Backfires and Spark Plugs

Learn what a back fire is and how to fix it.

Prepping Your Sled for the Season and the Importance of Spark Plugs

A pre-season tune-up can save you some major pains down the road.

Tips and Techniques from Lucas Oil to Keep Vehicles and More Protected During the Cold

Supercars, motorcycles, hot rods and even riding lawn mowers all have engine oil systems, fuel systems, transmissions and other components that require winter prep.

Lucas Oil